Raspberry Pi Camera Autofocus: The Complete Guide (V1, V2, HQ)

This article explains everything you need to know about the Raspberry Pi camera autofocus. 

It applies to all Raspberry Pi Models, and all Raspberry Pi camera modules: V1.3, V2.1, HQ, and V3.

Luckily, you are in the right place. Arducam has the most extensive solution to autofocus on Pi cameras.

So let’s dive right in and clarify this issue once and for all.

Prerequisites for autofocus

Here is the definition of autofocus from Wikipedia:

An autofocus (or AF) optical system uses a sensor, a control system, and a motor to focus on an automatically or manually selected point or area.

Easily, we get all the answers we need. Here are the 3 prerequisites for autofocus:

  1. Sensor
  2. Focus motor
  3. Control system
raspberry pi camera autofocus prerequisites
Sensor, focus motor, and control system are the 3 prerequisites of autofocus

To focus is to move the lens. To autofocus is to automatically move the lens.

The focus motor is the “what” to move the lens, and the control system is the “how” to move the lens. When we focus manually, our hands function like the focus motor, and our brain functions like the control system.

Therefore, autofocus does not mean no focusing process is involved. It’s just that the focus motor and the control system take over the job for your hand and your brain.

Well, do the Raspberry Pi cameras meet these prerequisites?

Do the official Raspberry Pi cameras meet all autofocus prerequisites?

For now, only the Camera Module 3 series has autofocus.

Let’s go over the prerequisites list again and see how the official Raspberry Pi cameras match.

  1. Sensor – Yes. They have CMOS image sensors.
  2. Focus motor – The V1.3 is glued and fixed. The V2 and HQ need manual work. All V3 cameras come with autofocus lenses, so yes.
  3. Control system – Only the V3 series.
Do the official Raspberry Pi cameras meet all autofocus prerequisites
raspberry pi camera V1, V2 and HQ only meet 1 of the 3 prerequisites, so it won’t do autofocus

The first 3 official Raspberry Pi cameras are not designed with autofocus in mind, instead, they just meet the basic needs.

The idea of the basic needs goes like this: You can get a clear picture with manual focus. The focus motors and control system not only add to the complexity but also add to the cost. Not everyone needs that. No need to meet all autofocus prerequisites.

Does this mean the official Pi cameras can’t do autofocus?

Yes. The first 3 official Raspberry Pi camera modules (V1/V2/HQ) cannot do autofocus themselves, period.

Does this mean there is no hope for Pi cameras to do autofocus?

Absolutely not. Arducam has fixed the issue and made it possible.

How does Arducam meet the Raspberry Pi Camera Autofocus prerequisites?

The logic to fix the issues is simple: 

For those Pi cameras that don’t have a focus motor and a control system, then we build variants that do. 

Let’s break down the two unmet prerequisites one by one.

1. Add Focus motor to the Pi camera

First, it’s the focus motor.

Let’s consider the focus motor a part of the lens assembly.

In case you don’t know, there are two kinds of lens assembly in Raspberry Pi cameras:

  1. The V1 and V2 have sealed the lens assembly and the image sensor in one package, then connected to the camera PCB with a board-to-board (BTB) connector. This design is also known as Compact Camera Modules (CCM), and it’s the kind used in smartphones.
  2. The HQ camera has a dedicated lens mount. Instead of having the image sensor in one package as the lens assembly, the IMX477 image sensor of the HQ camera is on the camera PCB.
filp-smartphone-camera-module-raspberry-pi-camera-off-blog
The detachable compact camera module on Raspberry Pi Camera Module V2
raspberry pi high quality hq camera ir filter
The Raspberry Pi High Quality Camera has the image sensor on the camera PCB

This leads us to two methods to design a Pi camera that support autofocus:

  1. We build a CCM with a focus motor inside, and then connect it to the Raspberry Pi Camera PCB.
  2. We build a special lens assembly with a focus motor and mount it above the image sensor onboard.
raspberry pi camera autofocus v2
CCM Autofocus replacement on the official V2 Camera Board
raspberry pi camera autofocus imx477 high quality camera hq
Special Autofocus lens assembly on Arducam’s own variants of IMX477 Camera Board

2. Add Control system (so the Pi can control the focus motor)

Second, it’s the control system. The Raspberry Pi should be able to control the focus motor.

Let’s consider how the Raspberry Pi is connected to the focus motor before we set up the connection:

  1. Raspberry Pi →
  2. → RPi MIPI CSI connector →
  3. → Camera Ribbon Cable →
  4. → Camera Module MIPI CSI Connector →
  5. → Camera Board →
  6. → Focus Motor.

From above, we know that the key physical connection is the MIPI CSI camera ribbon cable. If so, do we have anything on the MIPI CSI connection that can help us control the motor?

I2C bus. More specifically, the I2C for the VideoCore processor.

i2c_vc

Set to “on” to enable the i2c interface, usually reserved for the VideoCore processor (default “off”).

raspberry pi camera pinout i2c
I2C in raspberry pi camera pinout, useful for controlling the focus motor

So, we use the i2c_vc to control the motor. What we need to do is to add the following line to the /boot/config.txt.

dtparam=i2c_vc=on

Now that we’ve met the prerequisites, what else is needed?

How to enable the autofocus feature once we’re ready?

The last thing to do is to automate the focus process with a program.

Step 1: Software-controlled motorized focus

Let’s first get the motors moving.

With a simple python program, we can use the keyboard keys to move the focus motor.

If you are interested in how we’ve done that, here is the python code for software motorized focus control.

Software motorized focus Python code

import os
import time
import sys
import threading
import pygame,sys
from pygame.locals import *
from time import ctime, sleep
pygame.init()
screen=pygame.display.set_mode((320,240),0,32)
pygame.key.set_repeat(100)
def runFocus(func):
 temp_val = 512
 while True:
   for event in pygame.event.get():
	if event.type ==KEYDOWN:
           print temp_val
	   if event.key == K_UP:
              print 'UP'
	      if temp_val < 1000:
		     temp_val += 10
	      else:
		     temp_val = temp_val
              value = (temp_val<<4) & 0x3ff0
              dat1 = (value>>8)&0x3f
	      dat2 = value & 0xf0
              
              os.system("i2cset -y 0 0x0c %d %d" % (dat1,dat2))
           elif event.key==K_DOWN:
	      print 'DOWN'
	      if temp_val <12 :
                     temp_val = temp_val
              else:
                     temp_val -= 10
              value = (temp_val<<4) & 0x3ff0
              dat1 = (value>>8)&0x3f
              dat2 = value & 0xf0
              os.system("i2cset -y 0 0x0c %d %d" % (dat1,dat2))

def runCamera():
    cmd = "sudo raspistill -t 0"
    os.system(cmd)
if __name__ == "__main__":
 t1 = threading.Thread(target=runFocus,args=("t1",))
 t1.setDaemon(True)
 t1.start()	
 runCamera()

Now we get a camera module with a software-controlled focus motor. That’s already a big step forward. You won’t have to focus near the camera module with your bare hands. Instead, you can sit remotely and adjust the focus with software.

Adjust the focus of a Pi camera with keyboard arrow keys

However, if we want to enable autofocus, we need the Raspberry Pi to decide whether the camera is in focus, and it should stop moving the focus motors. But how would the Pi know?

Step 2: Autofocus enabled by OpenCV

As the biggest open-source computer vision library, OpenCV can help us make the Pi smart enough to tell whether the camera is in focus – by contrast detection.

sudo apt-get install python-opencv

The intensity difference between adjacent pixels of the sensor naturally increases with correct image focus. Then the Pi can adjust the motor until the maximal contrast is detected.

Arducam provides an OpenCV-powered autofocus example in Python. Here is what the image looks like on Raspbian when it runs.

Raspberry Pi camera autofocus in Raspbian

If you are interested in how we’ve done that, here is the python code for autofocus.

Autofocus.py

import cv2 #sudo apt-get install python-opencv
import numpy as py
import os
import time
import smbus
bus = smbus.SMBus(0)
try:
	import picamera
	from picamera.array import PiRGBArray
except:
	sys.exit(0)
	
def focusing(val):
	value = (val << 4) & 0x3ff0
	data1 = (value >> 8) & 0x3f
	data2 = value & 0xf0
       	# time.sleep(0.5)
        print("focus value: {}".format(val))
       # bus.write_byte_data(0x0c,data1,data2)
	os.system("i2cset -y 0 0x0c %d %d" % (data1,data2))
	
def sobel(img):
	img_gray = cv2.cvtColor(img,cv2.COLOR_RGB2GRAY)
	img_sobel = cv2.Sobel(img_gray,cv2.CV_16U,1,1)
	return cv2.mean(img_sobel)[0]

def laplacian(img):
	img_gray = cv2.cvtColor(img,cv2.COLOR_RGB2GRAY)
	img_sobel = cv2.Laplacian(img_gray,cv2.CV_16U)
	return cv2.mean(img_sobel)[0]
	

def calculation(camera):
	rawCapture = PiRGBArray(camera) 
	camera.capture(rawCapture,format="bgr", use_video_port=True)
	image = rawCapture.array
	rawCapture.truncate(0)
	return laplacian(image)
	
	
if __name__ == "__main__":
    #open camera
	camera = picamera.PiCamera()
	
        #camera.awb_gains=4
        #camera.exposure_mode='off'	
        #camera.awb_mode='fluorescent'
        #open camera preview
	camera.start_preview()
	#set camera resolution to 640x480(Small resolution for faster speeds.)
	camera.resolution = (640, 480)
        time.sleep(0.1)
	print("Start focusing")
	
	max_index = 10
	max_value = 0.0
	last_value = 0.0
	dec_count = 0
	focal_distance = 10


        

	while True:
	    #Adjust focus
		focusing(focal_distance)
		#Take image and calculate image clarity
		val = calculation(camera)
		#Find the maximum image clarity
		if val > max_value:
			max_index = focal_distance
			max_value = val
			
		#If the image clarity starts to decrease
		if val < last_value:
			dec_count += 1
		else:
			dec_count = 0
		#Image clarity is reduced by six consecutive frames
		if dec_count > 6:
			break
		last_value = val
		
		#Increase the focal distance
		focal_distance += 15
		if focal_distance > 1000:
			break

    #Adjust focus to the best
	focusing(max_index)
	time.sleep(1)
	#set camera resolution to 2592x1944
	camera.resolution = (1920,1080)
	#save image to file.
	camera.capture("test.jpg")
	print("max index = %d,max value = %lf" % (max_index,max_value))
	#while True:
	#	time.sleep(1)
		
	camera.stop_preview()
	camera.close()

Next Level: Raspberry Pi Camera Autofocus with PTZ (Pan-tilt-zoom) cameras

Now that we’ve understood the camera I2C can be used as a control signal to move the lens, we can take it even further.

If to focus is to move the lens, then to zoom is to move the elements inside the lens.

We want to control not only the lens but also the elements inside the lens: we can have an autofocus zoom lens. Together with pan and tilt servos, we build a PTZ camera for the Raspberry Pi with autofocus possibilities.

Pivariety: Using Raspberry Pi’s Own ISP Tuning Algorithms with Autofocus Cameras

The Pivariety Project brings Pi’s hardware ISP tuning and camera control algorithms to more camera modules.
With better support (AE, AWB, and AF), our autofocus cameras can not only focus faster but also can produce higher quality images/videos than those native camera modules.

Suggestions and Recommendations

That’s everything about how we’ve made autofocus possible on Raspberry Pi cameras. However, here are some of our suggestions:

  1. Autofocus is possible but don’t expect it to be as smooth or accurate as a smartphone camera. Arducam’s main goal is to prove the feasibility and offer you more possibilities. It’s OpenCV-based software focus, and it is incomparable to those fancy PD or laser autofocus.
  2. An Autofocus example is provided, but we would still recommend that you use the manual control in the software way. We provide another example that allows you to focus the camera in a more intuitive way – by tapping the keyboard arrow keys. It’s more accurate to help you focus on your region of interest (ROI).
  3. We’ve only tested our examples on Raspberry Pi OS (Raspbian), so not sure about the other operating systems. However, moof and jneilliii have provided an Octoprint plugin that allows you to control the focus motor, called ArduCamFocus.

That being said, here are V1,V2 and HQ Arducam camera modules that support autofocus features. 

The 5MP V1 and 12MP HQ cameras are a full camera module, and that means you can directly plug its camera ribbon cable into the Raspberry Pi’s CSI slot. The 8MP V2 version is a drop-in CCM replacement, and you need to detach the one on your V2 camera PCB and then attach this one to it.

Standard autofocus camera module for Raspberry Pi

Pivariety autofocus camera module for Raspberry Pi

PTZ(Pan-tilt-zoom) Pi camera module

Arducam 16MP-AF & 64MP-AF


Well, that brings us to the end of this overview.​

To conclude: The official Raspberry Pi camera modules do not support autofocus, but Arducam has made it possible to achieve autofocus by controlling a focus motor in our customized module via I2C.

​Why do you need the camera module to do autofocus on Raspberry Pi?

Leave your comments below!

0
Your Cart is empty!

It looks like you haven't added any items to your cart yet.

Browse Products